Emerson Tescom ER5000 Series Скачать руководство пользователя страница 226 | Manualshive

Страница: 226 / 248

Emerson Tescom ER5000 Series Скачать руководство пользователя страница 226

ER5000

—

226

Internal Variables

ER5000 Configuration Variables

09 ID_CONTROL_MODE

This variable establishes the control mode for the controller.
A value of four only occurs when a Control Limit has been
exceeded. See variables #54 (ID_MIN_AD_SETPOINT)
through #64 (CONTROL_LIMIT_STATE). A value of five only
occurs if the controller is in ESTOP, emergency stop, mode.

•

0 => internal feedback mode

•

1 => external feedback mode

•

2 => cascade mode

•

3 => manual mode

setpoint = 0x08fa => inlet open
setpoint = 0x0800 => solenoids closed
setpoint = 0x0706 => exhaust open

•

4 => control limit mode (read only)

•

5 => emergency stop (read only)

42 ID_NODE

This is the unit’s network Node Address. Note that if this
variable is changed then all future communication must be
addressed to the new Node Address.

52 ID_SERIAL_NUMBER

This is the serial number for the unit. It is programmed at the
factory and should not be changed by the user.

53 ID_VERSION_NUMBER

This is the version number of the embedded software.

120 ID_MODE_ER3000_ER5000

This is the selected mode of operation determined by either
installing or removing Jumper J9.

•

0 => ER5000 mode

•

1 => ER3000 mode

NOTE

NOTE

CAUTION

CAUTION

WARNING

WARNING

The unit must be powered down/up for the jumper change

to be recognized.

122 ID_SETPONT_RESET

This variable establishes the startup setpoint of the ER5000.
When it is activated (value = 1) the ER5000 will startup
at zero.

«
...
224
225
226
227
228
...
»

Содержание Tescom ER5000 Series

























































































































































































































































Отзывы:

Нет отзывов