Emerson Rosemount 3812 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 132

background image

35. Reattach the Transmitter Electronics Enclosure to the Base Enclosure with the four

hex head bolts and lock washers. Tighten bolts with a 7/16 inch (11mm) wrench.

36. Retighten or reattach the conduit to the Transmitter Electronics Enclosure using a

crescent wrench or channel lock pliers.

37. Apply electrical power to the meter.
38. Connect to the meter with MeterLink and run the Zero Flow Calibration Wizard;

select the

Calibrate

→

Zero Calibrate

menu and generate the report. Then, collect

and save a Maintenance log to show the “as left” condition of the meter. Or use
AMS

™

Device Manager or a HART

®

Field Communicator and select

Overview

→

Zero Calibration

→

Start menu

or

Service Tools

→

Maintenance

→

Zero

Calibration

→

Start

.

39. Close your application connection (MeterLink, AMS

™

Device Manager or HART

®

Field Communicator).

40. For band shroud meters only, re-inspect the transducer cables being held in the

body top cable grooves and body circular grooves and re-inspect the cable loop at
the body transducer pocket. Insure that the transducer cables will not be pinched
when the band shrouds are installed.

41. For split shroud meters only, inspect the transducer cables to be sure they will not

be pinched as the lower shroud is assembled. Make sure the transducer cables are
moved out of the way and will not be pinched when the Shroud is reinstalled.

42. Reinstall the shroud:

•

Install bolted band shrouds

•

Install clamped band shrouds

•

Install split shrouds

•

Install latched band shroud

43. Reseal the meter electronics and shroud, if required (see

).

This completes the transducer installation procedure for meters with direct mount
transmitter electronics.

3.7.2

Replace transducers remote mount transmitter
electronics

The meter has integrally mounted transducer cables that require you to disconnect the
cables from the terminal blocks inside the Junction Box and remove the transducer capsule
from the housing. This includes removing the Junction Box assembly from the meter body
and disconnecting the terminal blocks and transducer cable wiring.

Tip

The transducers are installed in matched pairs. Always replace the transducer pair of equal
path lengths (A1 and A2 or B1 and B2). Also, if a transducer pair is moved from one chord
position to another, the transducer pair’s delay time and delta delay time configuration
parameters must be properly re-configured.

Maintenance and Troubleshooting Manual

Meter maintenance

00809-0100-3812

April 2022

Rosemount 3812 Liquid Ultrasonic Flow Meter

77

«
...
75
76
77
78
79
...
»

Содержание Rosemount 3812





































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount 3812

Бренд: C-LOGIC Страницы: 2

Бренд: Abbott Страницы: 296

Бренд: Hach Страницы: 28

Бренд: J.P. Instruments Страницы: 9

Бренд: J.ASSY Страницы: 13

Бренд: La Crosse Technology Страницы: 8

Бренд: Vanguard Instruments Company Страницы: 62

Бренд: Vanguard Instruments Company Страницы: 58

Бренд: UNI-T Страницы: 11

Бренд: E+E Elektronik Страницы: 96

Бренд: Parker Страницы: 24

VirtualBench VB-8012

Бренд: National Instruments Страницы: 4

Бренд: KJ Instrument Страницы: 8

HD52.3D... series

Бренд: DeltaOHM Страницы: 46

Бренд: geo-FENNEL Страницы: 56

Бренд: Tonghui Страницы: 120

CubicSecure LTCS01

Бренд: Quandify Страницы: 11

VarioView Camera

Бренд: LaserLiner Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды