Emerson Rosemount 3812 Скачать руководство пользователя страница 92

Страница: 92 / 132

Figure 3-56: Liquid Ultrasonic Flow Meter electronics

A. Terminal end of Transmitter Electronics Enclosure

B. Backplane board location

C. End cap security latch

D. Base enclosure with Acquisition Module

3.9.1

Replace the CPU Module

Procedure

1. Disable electrical power to the meter.
2. Refer to

Table 3-9

for the tools required to complete this procedure.

3. Disconnect security seals on the Transmitter Electronics Enclosure, loosen the end

cap security latches using a 3 mm Allen wrench and remove both end caps from the
Transmitter Electronics Enclosure.

4. If replacing the CPU Module (located closest to the terminal end of the enclosure) or

the Optional I/O Module, use a 3mm flat blade screw driver and disconnect the CPU
Module terminal blocks (or the Optional I/O Module) terminal blocks).

Note

The Optional I/O Module is scheduled for future release.

Meter maintenance

Maintenance and Troubleshooting Manual

April 2022

00809-0100-3812

Emerson.com/Rosemount

Содержание Rosemount 3812





































































































































Результаты поиска

Содержание Rosemount 3812

Отзывы:

Похожие инструкции для Rosemount 3812

Бренды по названию

Популярные бренды

Emerson Rosemount 3812, Руководство по техническому обслуживанию и устранению неисправностей

Результаты поиска

Содержание Rosemount 3812

Отзывы:

Похожие инструкции для Rosemount 3812

Бренды по названию

Популярные бренды