Emerson Rosemount 3812 Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 132

background image

Figure 3-61: Power Supply Board replacement

A. Non-terminal end of Transmitter Electronics Enclosure

B. Power Supply board

C. I.S. Barrier board (inside the Guide Plate)

D. Backplane board

6. Pull the Backplane board out of the enclosure. This disconnects the I.S. Barrier

Board. Lay the Backplane board down with the Acquisition Cable still attached (the
Power Supply board may remain attached to the Backplane when you remove it
from the enclosure).

7. Plug the new Power Supply board and the I.S. Barrier Board onto the Backplane

Board.

8. Insert the Backplane, I.S. Barrier board and the Power Supply Board into the

enclosure and fully seat the CPU Module and Optional I/O Module.

9. Attach the Backplane to the enclosure standoffs with the four Phillips head screws.

10. Use a 1/8 inch (3 mm) flat blade screw driver and install the terminal blocks on the

CPU Module, Optional I/O Module, I.S. Barrier Board and the Power Supply.

11. Recheck the connections, wiring and switch settings before replacing the end caps.
12. Connect to the meter with MeterLink. Open the Meter Monitor (Detailed) view and

verify the meter is acquiring data, the transducers have good signals and flow
profiles for the chords are displayed and run the Zero Flow Calibration Wizard;
select the

Calibrate

→

Zero Calibrate

menu and generate the report. Then, collect

and save a Maintenance log to show the “as left” condition of the meter. Or use

Meter maintenance

Maintenance and Troubleshooting Manual

April 2022

00809-0100-3812

100

Emerson.com/Rosemount

«
...
98
99
100
101
102
...
»

Содержание Rosemount 3812





































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount 3812

TUNICS T100S-HP

Бренд: Yenista Optics Страницы: 66

Бренд: HANYOUNG NUX Страницы: 4

Бренд: jenway Страницы: 30

Бренд: National Meter & Automation Страницы: 24

Бренд: Lakeshore Страницы: 2

Бренд: Kamstrup Страницы: 4

Бренд: Hach Страницы: 38

Бренд: Hach Страницы: 28

Бренд: Hach Страницы: 40

POCKET COLORIMETER II

Бренд: Hach Страницы: 142

Бренд: Hach Страницы: 4

Бренд: Hach Страницы: 308

Бренд: Hach Страницы: 158

Бренд: Hach Страницы: 118

POCKET COLORIMETER II

Бренд: Hach Страницы: 116

Бренд: Hach Страницы: 132

Бренд: Hach Страницы: 8

Бренд: Hach Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды