Emerson Rosemount 3812 Скачать руководство пользователя страница 84

Страница: 84 / 132

18. Insert the transducer capsule into the transducer housing inside the meter body.
19. Slide the spring, shoulder washer and retaining ring onto the transducer cable.

Insert these components into the transducer housing.

Figure 3-50: Transducer cable assembly

A. Feed-thru cable seal

B. Retaining ring

C. Shoulder washer

D. Spring

E. Transducer capsule

F. Transducer housing

20. Insert the Feed-thru cable seal into the housing groove with the Retaining Ring

pliers (see

Figure 3-50

21. For band shroud meters only, loop the transducer cable at the transducer a couple

of turns. The loop must fit within the body transducer pocket.

a) Place the cable into the circular body groove at the transducer.

b) Use foil tape to hold the cable and loop in position.

c) Continue positioning the cable in the body circular groove and securing with

the tape. At the meter top, position the cable in the body top cable groove
and tape to hold.

d) Ensure that a flat surface will be available for the band shroud to be installed

without squeezing the transducer cable. Repeat for each transducer being
replaced.

Meter maintenance

Maintenance and Troubleshooting Manual

April 2022

00809-0100-3812

Emerson.com/Rosemount

Содержание Rosemount 3812





































































































































Результаты поиска

Содержание Rosemount 3812

Отзывы:

Похожие инструкции для Rosemount 3812

Бренды по названию

Популярные бренды

Emerson Rosemount 3812, Руководство по техническому обслуживанию и устранению неисправностей

Результаты поиска

Содержание Rosemount 3812

Отзывы:

Похожие инструкции для Rosemount 3812

Бренды по названию

Популярные бренды