Emerson Rosemount 3812 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 132

background image

Table 3-1: Contents-Transducer maintenance

(continued)

Maintenance task

Description

Section

Install the shrouds

•

Band shroud options

•

Bolted shroud (2” -3”
meters)

•

Clamped shroud (12” and
larger)

•

Split shroud (4” to 10”
meters)

•

Latched shroud (2” to 10”
meters)

•

Shrouds installation

•

Install bolted band shrouds

•

Install clamped band shrouds

•

Install split shrouds

•

Install latched band shroud

Seal the meter

Seal the meter electronics and
transducers

•

Seal direct or remote mount
transmitter electronics
enclosure

•

Seal direct or remote mount
transmitter electronics
enclosure

•

Seal direct or remote mount
Base electronics enclosure

3.2

Important safety information

Follow these safety message instructions to avoid injury and equipment damage.

CAUTION

SURFACE TEMPERATURE HAZARD
Meter body and piping may be extremely hot or cold.
Wear appropriate personal protective equipment when coming in contact with the meter.
Failure to comply may result in injury.

CAUTION

TRANSPORTATION HAZARD
When moving the meter, do not insert the forks of a forklift into the bore.
Inserting the forks may cause the meter to become unstable, resulting in injury to
personnel or damage to the bore and sealing face.

CAUTION

TRIPPING HAZARD
Clear all obstacles or obstructions from the work area when transporting, installing or
removing the meter.
Failure to comply may cause injury to personnel.

Meter maintenance

Maintenance and Troubleshooting Manual

April 2022

00809-0100-3812

38

Emerson.com/Rosemount

«
...
36
37
38
39
40
...
»

Содержание Rosemount 3812





































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount 3812

DigitalFlow XMT868i

Бренд: Panametrics Страницы: 74

Бренд: Larson Davis Страницы: 193

Бренд: Facom Страницы: 116

Бренд: Oldham Страницы: 43

Бренд: Omer Страницы: 2

Бренд: Bacharach Страницы: 87

Бренд: Kane Страницы: 19

Бренд: Cablescan Страницы: 58

Бренд: Lake Shore Cryotronics Страницы: 97

micro-TRI-gloss ?

Бренд: BYK Страницы: 174

Stream Line Pro

Бренд: Halo Photonics Страницы: 45

Stubby LED-1500

Бренд: Dive Perfect Страницы: 4

Micro Alti Vario Plus

Бренд: Fairhaven Страницы: 20

Бренд: ZETA Music Systems Страницы: 10

Бренд: Komshine Страницы: 2

DMX Laser40 FScan

Бренд: KAM Страницы: 4

Бренд: RADWAG Страницы: 12

Бренд: Lisle Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды