Emerson Rosemount 3812 Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 132

background image

NOTICE

Make sure the terminal blocks are aligned with the Guide Plate openings.

14. Recheck the connections, wiring and switch settings before replacing the end caps.
15. If replacing other electronics, continue with the following sections before replacing

the end caps and sealing the enclosure.

16. If you are not replacing other electronics, replace the end caps, security latches,

reseal the meter and apply power. If required, install the security seals through the
hex bolts in the Junction box cover (see

Seal the Junction Box for remote mount

electronics option

).

17. Apply power to the meter.
18. Connect to the meter with MeterLink. Open the Meter Monitor (Detailed) view and

verify the meter is acquiring data, the transducers have good signals and flow
profiles for the chords are displayed and run the Zero Flow Calibration Wizard;
select the

Calibrate

→

Zero Calibrate

menu and generate the report. Then, collect

and save a Maintenance log to show the “as left” condition of the meter. Or use
AMS

™

Device Manager or a HART

®

Field Communicator and select

Overview

→

Zero Calibration

→

Start

menu or

Service Tools

→

Maintenance

→

Zero

Calibration

→

Start

.

19. Close your application connection (MeterLink, AMS

™

Device Manager or HART

®

Field Communicator).

20. This completes the Backplane board replacement procedure.

If you encounter problems with this procedure, see the Emerson Customer Support
contact information on the back cover of this manual.

3.9.4

Replace the I.S. Barrier board

Procedure

1. If replacing the I.S. Barrier board, remove power to the meter.
2. Refer to

for the tools required to complete this procedure.

3. Disconnect the Transmitter Electronics Enclosure security seals, loosen the end cap

security latches with a 3mm Allen wrench and remove both end caps (see

).

4. Use a 1/8 inch (3 mm) flat head screw driver and remove the terminal blocks from

the Power Supply board, the CPU Module and the Optional I/O Module. See

for board locations and associated terminal blocks.

5. Use a Phillips head screw driver and remove the four Backplane board screws from

the enclosure standoffs.

6. Pull the Backplane board out of the enclosure. This disconnects the I.S. Barrier

Board. Lay the Backplane board down with the Acquisition Cable still attached (the
Power Supply board may remain attached to the Backplane when you remove it
from the enclosure).

Maintenance and Troubleshooting Manual

Meter maintenance

00809-0100-3812

April 2022

Rosemount 3812 Liquid Ultrasonic Flow Meter

97

«
...
95
96
97
98
99
...
»

Содержание Rosemount 3812





































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount 3812

Бренд: Omega Engineering Страницы: 22

Бренд: Bante Instruments Страницы: 6

Бренд: Danfoss Страницы: 6

Бренд: Kane Страницы: 16

Бренд: Kane Страницы: 60

Бренд: Kawai Страницы: 22

Concert Performer CP3

Бренд: Kawai Страницы: 40

Бренд: Kawai Страницы: 36

Бренд: Kawai Страницы: 148

Бренд: Kawai Страницы: 30

Classic Series CS6

Бренд: Kawai Страницы: 96

Бренд: Katronic Страницы: 3

FLUXUS ADM 6725

Бренд: Katronic Technologies Страницы: 148

Бренд: Kawai Страницы: 176

Бренд: LATNEX Страницы: 55

Бренд: Laser Technology Страницы: 11

Бренд: Laser Technology Страницы: 62

Бренд: Vaisala Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды