Emerson Rosemount 3812 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 132

background image

2.1.3

Chord A and Chord B alarm

Chord A and Chord B - These alarms indicate how a chord is functioning.

LED Color

Problem

Green

No alarms are present. Chord is operating properly.

Yellow

At least one sample in the batch caused an alarm but it did not
cause the chord to fail. The sample will not be used in the batch.
Discarding occasional samples can occur during normal operation
such as during flow velocity changes.

Red

The chord has failed or is in acquisition. This chord is not used for
this batch. Chords that have failed or are shown to be in
acquisition for repeated batches indicates that the meter should
be inspected by a service technician.

Gray

The chord has manually been set to inactive, or option is not
available.

2.1.4

Field I/O alarm

Reports various field I/O devices that are in alarm. Click the

Check Status

button for more

details on specific alarms. The field does not appear if the meter does not support this
alarm.

2.1.5

Validity alarm

This alarm indicates that the meter may not be measuring accurately. Click

Check Status

to see a description of which validity alarms are active. The validity alarms

QMeter

and

QFlow

indicate an issue with the meter collecting enough information from the chords to

make an accurate measurement. The validity alarms for pressure and temperature
indicate that the value is above or below the alarm limits for these values. Red and green
are the only colors used for this alarm.

2.1.6

Comms alarm

The Comms alarm indicates that communications between MeterLink and the meter
failed. This could be due to a poor communication link. MeterLink continues to retry
communications. Red and green are the only colors used for this alarm.

2.1.7

Communications

The Communications Analyzer (via

MeterLink Tools

→

Menu

→

Communications

Analyzer

menu path) displays communications between MeterLink and the ultrasonic

meter. This utility is useful for troubleshooting communications to the meter. It displays
many of the TCP/IP commands between MeterLink and the connected meter. For
troubleshooting communications with the 475 Field Communicator for the HART

®

Protocol, refer to Section 5 of the Emerson 475 Field Communicator User’s Manual, Rev D.

Maintenance and Troubleshooting Manual

Troubleshooting

00809-0100-3812

April 2022

Rosemount 3812 Liquid Ultrasonic Flow Meter

15

«
...
13
14
15
16
17
...
»

Содержание Rosemount 3812





































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount 3812

Бренд: TaiDoc Страницы: 31

WJHD309 - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 101

Бренд: Candela Страницы: 4

Network Card-MS

Бренд: Eaton Страницы: 26

Ultraprobe 9000

Бренд: UE Systems Страницы: 25

ULTRAPROBE 10000

Бренд: UE Systems Страницы: 6

Clavinova CVP-805

Бренд: Yamaha Страницы: 112

Clavinova CLP-270

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 3

Professional Plus

Бренд: YSI Страницы: 28

Бренд: Parkside Страницы: 120

Бренд: Alpes Lasers Страницы: 41

Бренд: Thermo Scientific Страницы: 56

Бренд: Velleman Страницы: 15

Бренд: Hanna Instruments Страницы: 12

Бренд: Xsens Страницы: 12

WIDE ANGLE CONVERSION PORT 2

Бренд: Nauticam Страницы: 12

Micropilot S FMR 53 Series

Бренд: E+H Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды