Emerson Rosemount 3812 Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 132

background image

Figure 3-68: Bolted band shroud - meter bottom view

A. Bolted band shroud

B. End shrouds

C. Bolt with lock washer installed

4. Hand tighten the bolt a few turns. Bend the shroud around the body OD and align

the hole near the other end of the shroud with the second tapped hole in the body
OD. Insert another bolt with lock washer and hand tighten.

5. Fully tighten one band shroud bolt.
6. Position the shroud as tightly to the meter body as possible and fully tighten the

shroud bolt.

7. Assemble the two end shrouds on to the end of the large outside diameter of the

body. Position the two end shrouds to cover the entire end surface aligning the two
holes created by joining the edges of the two end shrouds with the tapped holes in
the body end.

8. While holding the end shrouds insert one shroud bolt with lock washer into the

tapped hole and tighten wrench tight. Repeat with the second shroud bolt with lock
washer.

9. Repeat

to install the second bolted band shroud and two end

shrouds.
This completes the assembly of the bolted band shrouds.

3.10.2

Install clamped band shrouds

WARNING

CUTTING HAZARD
Sharp edges may be present on the band shrouds.
Wear appropriate personal protective equipment when working on the meter.
Failure to comply may cause serious injury.

Meter maintenance

Maintenance and Troubleshooting Manual

April 2022

00809-0100-3812

108

Emerson.com/Rosemount

«
...
106
107
108
109
110
...
»

Содержание Rosemount 3812





































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount 3812

Бренд: Badger Meter Страницы: 12

Бренд: Badger Meter Страницы: 16

Бренд: Badger Meter Страницы: 56

ModMAG M Series

Бренд: Badger Meter Страницы: 4

SMatrix DMX2400

Бренд: dallmeier Страницы: 12

Бренд: Mahr Страницы: 384

Бренд: National Instruments Страницы: 38

Бренд: Veeder-Root Страницы: 39

Бренд: Veeder-Root Страницы: 98

Бренд: VECTECH Страницы: 9

Бренд: Facom Страницы: 48

Бренд: Dräger Страницы: 538

Бренд: PICO Страницы: 2

Бренд: JUMO Страницы: 150

Бренд: Hanna Instruments Страницы: 11

Бренд: Vega Страницы: 20

Бренд: SAND Страницы: 15

Бренд: SNV Engineering Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды