E-FLITE Blade CP Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 68

background image

3

Introduction

The Blade

™

CP+ is the perfect “next step” for anyone who’s mastered the basics of heli flight with

a coaxial heli like the Blade CX (EFLH1200) or Blade CX2 (EFLH1250), and is ready for a model

capable of more advanced maneuvers. It’s also an excellent choice for experienced pilots looking for

the best in ready-to-fly micro helicopter performance.
The Blade CP+ includes all the impressive features of the original Blade CP, like CCPM and collective

pitch, plus a number of new features and accessories that further enhance its flight performance for

low-time and experienced pilots alike. The included, optional-use training gear set adds stability while

also providing support and cushioning to prevent tip-overs and rotor blade strikes for newer pilots.

The 3S 11.1V 800mAh Li-Po battery pack offers a significant boost in power and duration over the

Ni-MH batteries found in other similar class models, and the included, optional-use symmetrical main

rotor blades allow you to perform advanced aerobatics like loops, rolls and inverted flight without

the need for a single hop-up. The separate receiver and advanced 3-in-1 control unit are plug-and-

play compatible with brushless power systems and heading lock gyros so you can further enhance the

capabilities of your Blade CP+ when you’re ready to take performance to the next level.
And although the Blade CP+ is nearly ready-to-fly right from the box, please take the time to read

through this manual for tips on battery safety and charging, control checks, adjustments and more

before making your first flight.

Warning

An RC helicopter is not a toy! If misused, it can cause serious bodily harm and damage to property.

Fly only in open areas, preferably at AMA (Academy of Model Aeronautics) approved flying sites,

following all instructions.
Keep loose items that can get entangled in the rotor blades away for the main and tail blades,

including loose clothing, or other objects such as pencils and screwdrivers. Especially keep your hands

away from the rotor blades.

Note on Lithium Polymer Batteries

Lithium Polymer batteries are significantly more volatile than alkaline or Ni-Cd/Ni-MH batteries

used in RC applications. All manufacturer’s instructions and warnings must be followed closely.

Mishandling of Li-Po batteries can result in fire. Always follow the manufacturer’s instructions

when disposing of Lithium Polymer batteries.

Warranty Period

Horizon Hobby, Inc., (Horizon) warranties that the Products purchased (the “Product”) will be free from

defects in materials and workmanship at the date of purchase by the Purchaser.

«
1
2
3
4
5
...
»

Содержание Blade CP





































































Отзывы:

Нет отзывов

Похожие инструкции для Blade CP

SET OF FUNFAIR CARAVANS II

Бренд: Faller Страницы: 4

HALF-TIMBERED HOUSE

Бренд: Faller Страницы: 4

Бренд: Faller Страницы: 4

Бренд: Fisher-Price Страницы: 16

Бренд: Fisher-Price Страницы: 4

Antares C3M4 Combat Drone

Бренд: Warlord Games Страницы: 2

NORTH AMERICAN T-28 TROJAN

Бренд: SG Models Страницы: 34

80-072300 - Little Einsteins Learn

Бренд: VTech Страницы: 14

Бренд: Beyblade Страницы: 2

Бренд: BearCreeks Страницы: 19

BARBIE BEACH RANGER 78477

Бренд: Fisher-Price Страницы: 36

Бренд: Faller Страницы: 12

Бренд: Clas Ohlson Страницы: 32

E-Flite V-22 Osprey VTOL

Бренд: Horizon Hobby Страницы: 20

Бренд: Fisher-Price Страницы: 4

Бренд: Fisher-Price Страницы: 24

Бренд: Fisher-Price Страницы: 32

Бренд: Kayoba Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды