E-FLITE Blade CP Скачать руководство пользователя страница 52

Страница: 52 / 68

Optional Brushless Main Motor Power System Installation and Setup

The Blade CP+’s separate 6-channel FM receiver and 3-in-1 control unit allow you the option of

upgrading to a brushless main motor power system, without the need for difficult modifications or a

new radio system. An optional brushless main motor power system can provide added power and/or

duration when compared to the stock brushed main motor power system, and is an excellent choice for

those interested in maximizing the performance and aerobatic potential of their model.

Note: When installing a brushless main motor power system, we also highly recommend the

installation of an optional heading lock type gyro to help maximize performance of the tail due to

the added torque and performance the brushless main motor will provide.

We have tested a wide variety of motor types, in a wide range of Kv (rpm/v) values, and gear ratio

combinations in the Blade CP Pro. While many combinations offered a noticeable improvement in

power or duration when compared to the stock brushed motor, we found the following recommended

power system combination (and required supporting accessories) to provide the best balance of added

power while also maintaining good flight duration when using the included 3-cell 800mAh Li-Po

battery pack:

Item

Description

EFLA228

JST Female/2 JST Male Parallel Y-Harness

EFLA311B

20-Amp Brushless ESC

EFLM1000

Park 370 Brushless Inrunner Motor, 4100Kv

EFLM1912

Heat Sink, 20x20mm (optional)

EFLM1949

Pinion Gear, 8T 0.5 Module 2mm ID

EFLRYH3

3” Y-Harness

Содержание Blade CP





































































Результаты поиска

Содержание Blade CP

Отзывы:

Похожие инструкции для Blade CP

Бренды по названию

Популярные бренды

E-FLITE Blade CP, Руководство пользователя

Результаты поиска

Содержание Blade CP

Отзывы:

Похожие инструкции для Blade CP

Бренды по названию

Популярные бренды