E-FLITE Blade CP Скачать руководство пользователя страница 11

Страница: 11 / 68

Battery Charging

It is important that you only charge the included 3S 11.1V 800mAh Li-Po Battery Pack (EFLB0995)

with the included 3-Cell 11.1V Li-Po Balancing Charger (EFLC3105). Your battery pack is equipped

with special Charge Protection Circuitry and a Balance Charge Lead with connector that is only

compatible with this charger. Attempting to charge the pack using another Li-Po charger or non Li-

Po compatible charger could result in serious damage. Please familiarize yourself thoroughly with

the warnings and guidelines (pages 9–10) before continuing.

The included 3-Cell 11.1V Li-Po Balancing Charger will charge a near fully discharged (not over-

discharged) 3S 11.1V 800mAh Li-Po Battery Pack in approximately 1.2–1.5 hours. In some cases the

charge time may be shorter depending on the actual amount of capacity left in the pack after a flight.

NEVER charge the battery unattended.
Note

: The Li-Po battery pack included with your Blade™ CP+ will arrive partially charged. For this

reason the initial charge may only take approximately 30–50 minutes.
The charger requires up to 1.5 Amps of 11.5–15 Volt DC input power that can be supplied by the

optional AC to 12V DC, 1.5-Amp Power Supply (EFLC4000) for convenient charging anywhere an

AC outlet is available.

NEVER attempt to power the charger from an AC outlet without the use of a

proper AC to DC adapter/power supply.
Note

: When using the AC to DC adapter/power supply, the charger is protected to prevent damage if

the alligator clips touch one another. However, please take care to ensure that the alligator clips do not

cause shorting of the battery, adapter/power supply, etc. by keeping them clear.

Содержание Blade CP





































































Результаты поиска

Содержание Blade CP

Отзывы:

Похожие инструкции для Blade CP

Бренды по названию

Популярные бренды

E-FLITE Blade CP, Руководство пользователя

Результаты поиска

Содержание Blade CP

Отзывы:

Похожие инструкции для Blade CP

Бренды по названию

Популярные бренды