E-FLITE Blade CP Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 68

background image

19

Position the helicopter to view it from the left or right side. Move the left-hand stick up and down to

check the collective pitch control. When the stick is pushed up, the swashplate should lower, increasing

the pitch of the main blades.

With the stick pulled back down, the swashplate should raise, decreasing the pitch of the main blades.

«
...
17
18
19
20
21
...
»

Содержание Blade CP





































































Отзывы:

Нет отзывов

Похожие инструкции для Blade CP

COMET SENIOR DART

Бренд: Paul Bradley Страницы: 6

Бренд: K'Nex Страницы: 28

265 ALUTWIN 2,4G

Бренд: NINCOAIR Страницы: 21

Бренд: JR Страницы: 106

Бренд: Walkera Страницы: 31

Draganflyer X4-ES

Бренд: Draganfly Страницы: 82

Бренд: VQ Страницы: 1

Бренд: CYmodel Страницы: 10

Бренд: skyangel Страницы: 16

Electronic flash magic

Бренд: LeapFrog Страницы: 4

Techno Gears Marble Mania Mine Shaft 2.0

Бренд: The Learning Journey Страницы: 72

Goblin 570 Sport

Бренд: SAB Heli Division Страницы: 36

Бренд: Mega Bloks Страницы: 20

2-in-1 Journey Wagon 3379

Бренд: Radio Flyer Страницы: 2

Sopwith camel 3451

Бренд: LEGO Страницы: 52

Splash-n-Scrub Sink

Бренд: B.toys Страницы: 2

Бренд: Clas Ohlson Страницы: 34

Бренд: Clas Ohlson Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды