E-FLITE Blade CP Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 68

background image

13

Once you have connected the charger to a power source (use care to ensure proper polarity when

connecting the charger to the power source), its red LED will flash to indicate the charger has power

and is ready to begin charging. Connect the Li-Po battery pack to the charger using the specially

marked Balance Charge Lead exiting the battery pack and the connector labeled with 11.1V on the

charger. The connector is keyed to prevent reverse polarity connection.

When the battery is properly connected and charging normally, the red and green LED indicators

will glow solid. Once the battery has been fully charged, the green LED will go out, leaving just the

red LED glowing solid. The battery can now be removed from the charger and installed into the

Blade CP+ for flight.

«
...
11
12
13
14
15
...
»

Содержание Blade CP





































































Отзывы:

Нет отзывов

Похожие инструкции для Blade CP

Бренд: LaTrax Страницы: 11

Where Can We Go Wheel

Бренд: VTech Страницы: 10

Бренд: GRAUPNER Страницы: 21

Бренд: Chipolino Страницы: 5

Бренд: beeloom Страницы: 11

Бренд: Faller Страницы: 4

Бренд: Eduard Страницы: 3

Бренд: Faller Страницы: 4

Бренд: Composite-ARF Страницы: 23

ULTIMATE 20-300 ARF-QB

Бренд: AeroWorks Страницы: 94

Premier Chapelon 2-3-1E Pacific

Бренд: M.T.H. Страницы: 30

SPEED MASTER TG511

Бренд: THINK GIZMOS Страницы: 6

Бренд: Fisher-Price Страницы: 20

Бренд: bewello Страницы: 12

Бренд: Opitec Страницы: 7

Бренд: LEXIBOOK Страницы: 52

Бренд: Techone Страницы: 12

Бренд: RC Factory Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды