E-FLITE Blade CP Скачать руководство пользователя страница 53

Страница: 53 / 68

The following steps outline installation and setup of the recommended optional brushless power system:

• In order to provide the most secure motor mounting, and proper clearance for the forward bearing

cup in the main frame, it will be necessary to install the Park 370 brushless motor’s (EFLM1000)

included “Adapter Ring.”

• After installing the adapter ring, it will then be necessary to remove the stock brushed main motor from

the main frame in order to trial fit the brushless motor to check for proper placement of the pinion on

the brushless motor’s shaft.

Note:

Before removing the stock brushed main motor, we suggest that you check the gear mesh of its

9-tooth pinion and the main drive gear, in multiple places on the main drive gear, for reference. This

is approximately how you will want to set the pinion and main gear mesh after installing the brushless

motor and the 8-tooth pinion.

• Once the stock brushed main motor has been removed from the frame, temporarily install the Park

370 brushless motor. Then, using the 8-Tooth Pinion Gear (EFLM1949) and main gear for reference,

mark the shaft of the motor (using a marker or tape) at the point to which the pinion gear should

be press fit onto the shaft to provide adequate gear tooth contact of the pinion and main gear. It is

important to install the pinion on the motor shaft so that it will always offer full contact with the main

gear teeth in order to promote the best power transfer and to prevent uneven and/or accelerated gear

wear.

Содержание Blade CP





































































Результаты поиска

Содержание Blade CP

Отзывы:

Похожие инструкции для Blade CP

Бренды по названию

Популярные бренды

E-FLITE Blade CP, Руководство пользователя

Результаты поиска

Содержание Blade CP

Отзывы:

Похожие инструкции для Blade CP

Бренды по названию

Популярные бренды