E-FLITE Blade CP Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 68

background image

26

Installing the Training Gear

If the Blade CP+ is your first single-rotor and/or collective-pitch equipped helicopter model, we suggest

that you install the included Training Gear Set before making your first flight. The training gear helps

to further increase the stability of the model while also providing added support and cushioning to

prevent tip-overs and damage to the model from abrupt landings.
Installing the training gear takes only a few minutes following these steps:

• The Training Gear Set includes four plastic balls, four tubing keepers, four training gear rods, four

training gear rod-to-landing skid attachments and one training gear rod mounting base.

«
...
24
25
26
27
28
...
»

Содержание Blade CP





































































Отзывы:

Нет отзывов

Похожие инструкции для Blade CP

Бренд: GAUI Страницы: 32

Бренд: J. Perkins Страницы: 12

Бренд: GAUI Страницы: 28

Бренд: GAUI Страницы: 30

Бренд: LEGO Страницы: 36

Deere CONSTRUCTION LOADER

Бренд: Peg-Perego Страницы: 52

Touch & Learn Activity Desk Deluxe

Бренд: VTech Страницы: 10

LEGO STATUE OF LIBERTY 21042

Бренд: LIGHT MY BRICKS Страницы: 25

Бренд: T-Storm Страницы: 40

Call of Duty Dragonfire Drone Strike

Бренд: Mega Construx Страницы: 2

Бренд: Hornby Страницы: 2

Zoom F/A-18C Hornet S.A.

Бренд: Eduard Страницы: 3

Бренд: West Michigan Park Flyers Страницы: 14

Бренд: Fisher-Price Страницы: 4

Бренд: Redcat Racing Страницы: 15

Let it Roll! Bowling Alley

Бренд: Our Generation Страницы: 2

AJO THUNDERBOLT

Бренд: J-Power Страницы: 31

Бренд: Fisher-Price Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды