E-FLITE Blade CP Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 68

background image

37

Normal and Idle Up Flight Modes

The 6-channel FM transmitter included with your Blade CP+ features servo reversing and CCPM

mixing, as well as an “Idle Up” flight mode switch. This switch allows the pilot to toggle between

“normal” and “stunt” (aerobatic) flight modes during flight.

With the switch toggled toward the rear of the transmitter, the Blade CP+ will be flying in “normal

mode.” In this flight mode, the throttle curve is linear from 0% to 100%, with a pitch range of 0

degrees to +10 degrees. (See Page 40 for additional data and graphics relating to the throttle and

pitch curves preset for your Blade CP+.) This is the preferred flight mode for general hovering and

gentle forward flight.

Idle Up Switch

«
...
35
36
37
38
39
...
»

Содержание Blade CP





































































Отзывы:

Нет отзывов

Похожие инструкции для Blade CP

Бренд: Ultrafly Страницы: 16

STAR WARS 75102

Бренд: LEGO Страницы: 124

Бренд: Eduard Страницы: 4

Бренд: Faller Страницы: 8

Alexander Schleicher ASK 13

Бренд: Paolo Severin Страницы: 28

Aces Wild Custom Chopper

Бренд: REVELL Страницы: 8

STAR WARS 10221

Бренд: LEGO Страницы: 228

Flaglor Sky Scooter

Бренд: RC GROUP Страницы: 11

Бренд: Mega Bloks Страницы: 2

Zoom Wellington Mk.III S.A.

Бренд: Eduard Страницы: 3

Бренд: Fisher-Price Страницы: 6

Бренд: Fisher-Price Страницы: 6

Бренд: Eduard Страницы: 2

D9R Doobi cooling slats

Бренд: Eduard Страницы: 2

Бренд: VQ Страницы: 22

King Tiger fenders

Бренд: Eduard Страницы: 4

Бренд: Fisher-Price Страницы: 6

Бренд: Fisher-Price Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды