E-FLITE Blade CP Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 68

background image

18

Control Test

Although each Blade CP+ model is test flown at the factory, it is a good idea to test the controls prior

to the first flight to ensure none of the servos, linkages or parts were damaged during shipping and

handling.

Before proceeding, unplug both the main and tail motor plugs from the 3-in-1 control

unit making note of their direction and polarities for proper re-installation after the control test is

complete. It is not safe to perform the control test with the main or tail motor plugs connected to the

3-in-1 control unit after power up.

Turn the transmitter on first and lower the throttle stick and trim completely. Then, plug the battery into

the battery lead of the 3-in-1 unit.

«
...
16
17
18
19
20
...
»

Содержание Blade CP





































































Отзывы:

Нет отзывов

Похожие инструкции для Blade CP

Бренд: 2KRC Страницы: 17

K-FORCE Build and Blast 47518

Бренд: K'Nex Страницы: 2

ZOOM Do 217J-1/2

Бренд: Eduard Страницы: 4

BP PETROL STATION

Бренд: Faller Страницы: 8

Бренд: Carson Страницы: 26

LITTLE Chef DELUXE 200362

Бренд: Smyths Toys Страницы: 4

DODGEM CAR RIDE

Бренд: Faller Страницы: 12

Бренд: PARKZONE Страницы: 12

Premier Swiss 6/8 Type II Crocodile Electric Engine

Бренд: M.T.H. Страницы: 107

X-SA The GRASSHOPPER

Бренд: Tamiya Страницы: 6

ZM2603408WOW-000-000

Бренд: MOKIDA Страницы: 11

Бренд: Bestway Страницы: 6

Skippity Doo da

Бренд: B.toys Страницы: 2

National Geographic NG300 ICHTHYOSAUR

Бренд: Laser Pegs Страницы: 27

Бренд: Malibu Boats Страницы: 200

Fuzzikins Unicorn Sleepover FF009

Бренд: PlayMonster Страницы: 2

Бренд: Little Tikes Страницы: 2

Бренд: marklin Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды