E-FLITE Blade CP Скачать руководство пользователя страница 58

Страница: 58 / 68

• Because the receiver and servos will receive power from the 3-in-1 control unit, it will now be

necessary to disable the BEC power of the brushless ESC before connecting it to the receiver. To do

this, it will be necessary to remove the red (positive) lead and connector from the plastic housing that

goes to the receiver, then to insulate it properly to prevent shorting. Use a small screwdriver or knife

blade (and extreme care to prevent injury) to lift the plastic tab that secures the connector in the plastic

housing, then slide it out the back end of the housing. Use tape or shrink tubing to insulate and secure

the exposed connector.

Note: It is extremely important to disable the BEC of the brushless ESC in order to prevent damage

to the other electronics. Remember, BEC power is already supplied to the receiver and servos

through the 3-in-1 control unit throttle and rudder leads.

Содержание Blade CP





































































Результаты поиска

Содержание Blade CP

Отзывы:

Похожие инструкции для Blade CP

Бренды по названию

Популярные бренды

E-FLITE Blade CP, Руководство пользователя

Результаты поиска

Содержание Blade CP

Отзывы:

Похожие инструкции для Blade CP

Бренды по названию

Популярные бренды