E-FLITE Blade CP Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 68

background image

55

• Because the ESC does not include a battery connector, you will need to solder the Y-harness directly

to its battery power leads. To do this, remove one of the Y-harness’ JST male connectors from its wire

leads, as close to the end of the connector as possible. Then, strip the ends of the remaining wire leads

so that they can be soldered to the ESC’s battery power leads.

Note: It is extremely important to be sure that you remove one of the JST male connectors and not

the JST female connector. It is also critical that you maintain proper polarity (positive-to-positive and

negative-to-negative) when soldering the leads together, while also using shrink-tubing to insulate

the joints in order to prevent shorting.

«
...
53
54
55
56
57
...
»

Содержание Blade CP





































































Отзывы:

Нет отзывов

Похожие инструкции для Blade CP

30 model building set

Бренд: KNEX Страницы: 24

Lancaster B Mk.II bomb bay

Бренд: Eduard Страницы: 2

Бренд: Eduard Страницы: 4

Бренд: MTHTrains Страницы: 36

Zlin Z-37A Cmelak

Бренд: KOR MODEL Страницы: 21

Бренд: Pinolino Страницы: 12

E-flite Carbon-Z Cub SS

Бренд: Horizon Hobby Страницы: 24

ZAG HEROEZ Miraculous Pixelo

Бренд: Lansay Страницы: 2

Ju 88A interior S.A.

Бренд: Eduard Страницы: 2

Super PNP F-100D Super Sabre

Бренд: Flex innovations Страницы: 32

PowerTouch Baby H8052

Бренд: Fisher-Price Страницы: 12

Baby Annabell 700969

Бренд: Zapf Creation Страницы: 6

Бренд: GRAUPNER Страницы: 12

Бренд: battat Страницы: 2

He 111 H-6 bomb bay

Бренд: Eduard Страницы: 3

AERO SUBARU 30EP

Бренд: KK Hobby Страницы: 4

Бренд: marklin Страницы: 28

Бренд: F-One Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды