E-FLITE Blade CP Скачать руководство пользователя страница 46

Страница: 46 / 68

Optional Symmetrical Main Rotor Blade Installation

Your Blade CP+ is equipped with a set of flat bottom main rotor blades (EFLH1147A) right from the

box. These rotor blades offer the most possible lift for positive pitch (upright) maneuvers, and the

longest flight durations when hovering and performing upright forward and backward flight.
However, also included in the box is a set of optional-use symmetrical main rotor blades (EFLH1147B).

These blades feature a fully symmetrical airfoil that offers the same amount of lift when the model is

flown upright or inverted in the “Idle Up” flight mode and the appropriate amount of pitch is used. Use

of the symmetrical rotor blades will allow you to perform aerobatic maneuvers such as loops, rolls and

inverted flying.
Installation of the symmetrical main rotor blades takes just a few minutes. Use the 1.5mm hex wrench

included in the Mounting Accessories & Wrench bag to remove the main rotor blade mounting bolt

and nut from each blade grip. Remove the flat bottom main rotor blades and replace them with the

symmetrical main rotor blades. Be sure that the thicker section of the symmetrical rotor blades (the

leading edges) are to the front when the rotor blades spin in the clockwise direction (when viewed

from above).

Optional Heading Lock Gyro Installation and Setup

A unique feature of the Blade CP+ is that it allows you to install an optional “Heading Lock” type gyro

to further enhance the holding performance and response of the tail, without the need for difficult

modifications or an alternative radio system. While the stock “Standard Rate” type gyro contained

in the 3-in-1 control unit performs well for many types of flying, a heading lock gyro offers superior

tail holding power that helps to maintain heading throughout even the most aggressive aerobatic

maneuvers.
When installing a heading lock type gyro, we recommend the E-flite

G90 Sub-Micro Heading Lock

gyro (EFLRG90HL). The G90 gyro weighs only 9.0 grams (.32 oz), and features a very small footprint

that makes mounting it on the gyro mounting plate quick and easy. It’s an excellent choice when

looking for the best in tail and heading lock performance.

Содержание Blade CP





































































Результаты поиска

Содержание Blade CP

Отзывы:

Похожие инструкции для Blade CP

Бренды по названию

Популярные бренды

E-FLITE Blade CP, Руководство пользователя

Результаты поиска

Содержание Blade CP

Отзывы:

Похожие инструкции для Blade CP

Бренды по названию

Популярные бренды