E-FLITE Blade CP Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 68

background image

6

Additional Safety Precautions and Warnings

As the user of this product, you are solely responsible for operating it in a manner that does not

endanger yourself and others or result in damage to the product or the property of others.
This model is controlled by a radio signal that is subject to interference from many sources outside your

control. This interference can cause momentary loss of control so it is advisable to always keep a safe

distance in all directions around your model, as this margin will help to avoid collisions or injury.

• Never operate your model with low transmitter batteries.
• Always operate your model in an open area away from cars, traffic, or people.
• Avoid operating your model in the street where injury or damage can occur.
• Never operate the model out into the street or populated areas for any reason.
• Carefully follow the directions and warnings for this and any optional support equipment

(chargers, rechargeable battery packs, etc.) that you use.

• Keep all chemicals, small parts and anything electrical out of the reach of children.
• Moisture causes damage to electronics. Avoid water exposure to all equipment not specifically

designed and protected for this purpose.

• Never lick or place any portion of your model in your mouth as it could cause serious injury or

even death.

Additional Required Equipment

No additional equipment is required to complete your Blade CP+.

«
...
4
5
6
7
8
...
»

Содержание Blade CP





































































Отзывы:

Нет отзывов

Похожие инструкции для Blade CP

Бренд: Laser Pegs Страницы: 3

Lancaster B Mk.II bomb bay

Бренд: Eduard Страницы: 2

L-29 Delfín exterior

Бренд: Eduard Страницы: 2

Education STEM Explorations 79320

Бренд: K'Nex Страницы: 16

Бренд: Trix Страницы: 60

Бренд: Hot Wheels Страницы: 4

Бренд: Eduard Страницы: 6

imaginext J2532

Бренд: Fisher-Price Страницы: 12

TRACKMASTER T0787

Бренд: Fisher-Price Страницы: 1

Бренд: Oregon Scientific Страницы: 32

Lightning McQueen Learning Laptop

Бренд: VTech Страницы: 10

RC flying dragon

Бренд: goliath Страницы: 8

RAILKING GALLOPING GOOSE

Бренд: Rail King Страницы: 32

Focke-Wulf 190 D9

Бренд: Top Flite Страницы: 65

V.Flash: Scooby-Doo Ancient Adventure

Бренд: VTech Страницы: 20

Smokescreen 7051

Бренд: Hasbro Страницы: 16

Бренд: PICO Страницы: 2

CONVERGENCE VTOL

Бренд: Horizon Hobby Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды