E-FLITE Blade CP Скачать руководство пользователя страница 48

Страница: 48 / 68

• Remove the 3-in-1 control unit’s rudder channel lead (marked with a small label) from channel 4 of the

receiver, and plug this lead into the servo connector of the gyro. Then, plug the rudder channel lead of

the gyro into channel 4 of the receiver, ensuring proper orientation and polarity direction of the wire

leads.

• Because the transmitter included with your Blade CP+ does not offer proportional control of the fifth

channel, it will not be possible for you to use the remote gain control option of the G90 for setting

the gyro mode and gain from the transmitter. This means that the gyro’s auxiliary (AUX) lead and

connector will not be plugged into the receiver, so it will be necessary for you to secure the lead and

connector so they can not come into contact with any moving parts on the helicopter.

Note: It is important to secure the 3-in-1 rudder, gyro rudder and auxiliary channel leads so that

they can not come in contact with the pinion and main gear, servo arms or motor case. We suggest

using the cable/zip tie wraps included in the “Mounting Accessories & Wrench” package to secure

the leads to the main frame.

Содержание Blade CP





































































Результаты поиска

Содержание Blade CP

Отзывы:

Похожие инструкции для Blade CP

Бренды по названию

Популярные бренды

E-FLITE Blade CP, Руководство пользователя

Результаты поиска

Содержание Blade CP

Отзывы:

Похожие инструкции для Blade CP

Бренды по названию

Популярные бренды