E-FLITE Blade CP Скачать руководство пользователя страница 54

Страница: 54 / 68

• After confirming the point to which the pinion gear should be press fit onto the motor shaft, remove the

motor from the frame. Then, following the instructions included with the motor, install the pinion on the

motor shaft. The motor is now ready to install in the helicopter.

• Next, install the motor in the main frame using the mounting screws and washers removed from the

stock brushed main motor. It is a good idea to apply a small amount of threadlock compound (like

“blue” Loctite) to the threads before installing the screws. If possible, be sure to mount the motor so that

the leads exiting the rear of the case are positioned as close to the main shaft as possible in order to

help provide better clearance for the canopy. Do not tighten the mounting screws entirely until after the

next step.

• Take your time to set the gear mesh between the pinion and main gear properly. Then, tighten the

mounting screws securely.

Note: It is very important to set the gear mesh so that it is smooth with no binding. Be certain to

check the mesh as multiple points on the main gear in order to find the position in which to secure

the motor for the best gear mesh overall. Remember, if the gear mesh is set too loose or too tight, at

any point on the main gear, it may strip the gear and/or could cause a significant loss in power.

• After completing installation of the brushless motor, we also suggest that you install the 20x20mm Heat

Sink (EFLM1912). Be sure to follow the instructions included with the heat sink for proper installation.

• Next, it will be necessary to prepare the 20-Amp Brushless ESC (EFLA311B) for installation. For these

steps you will also need the JST Female/2 JST Male Parallel Y-Harness (EFLA228). This Y-harness

will be used to provide power to both the 3-in-1 control unit and brushless ESC from the Li-Po battery

pack.

Содержание Blade CP





































































Результаты поиска

Содержание Blade CP

Отзывы:

Похожие инструкции для Blade CP

Бренды по названию

Популярные бренды

E-FLITE Blade CP, Руководство пользователя

Результаты поиска

Содержание Blade CP

Отзывы:

Похожие инструкции для Blade CP

Бренды по названию

Популярные бренды