E-FLITE Blade CP Скачать руководство пользователя страница 8

Страница: 8 / 68

Preparing for the First Flight Checklist

Please note this checklist is not intended to be a replacement for the content included in this instruction

manual. Although it can be used as a quick start guide, we strongly suggest reading through this

manual completely before proceeding.



Remove and inspect contents



Charge the flight battery



Install the 8 included “AA” batteries in the transmitter



Install the flight battery in the helicopter (once it has been fully charged)



Check the Center of Gravity of the helicopter



Test the controls



Install the included Training Gear Set (strongly recommended if this is your first collective-pitch

equipped helicopter model)



Familiarize yourself with the controls



Find a suitable area for flying

Flying Checklist

Please note this checklist is not intended to be a replacement for the content included in this instruction

manual. Although it can be used as a quick start guide, we strongly suggest reading through this

manual completely before proceeding.



Always turn the transmitter on first



Plug the flight battery into the 3-in-1 control unit



Allow the 3-in-1 control unit to arm properly



Fly the model



Land the model



Unplug the flight battery from the 3-in-1 control unit



Always turn the transmitter off last

Содержание Blade CP





































































Результаты поиска

Содержание Blade CP

Отзывы:

Похожие инструкции для Blade CP

Бренды по названию

Популярные бренды

E-FLITE Blade CP, Руководство пользователя

Результаты поиска

Содержание Blade CP

Отзывы:

Похожие инструкции для Blade CP

Бренды по названию

Популярные бренды