SG Models NORTH AMERICAN T-28 TROJAN Скачать руководство пользователя | Manualshive

Страница: 1 / 34

background image

Instruction Manual.

1

A S S E M B L Y M A N U A L

Specifications:

Wingspan---------------63.0 in (160 cm).
Wing area---------------349.5 sq.in ( 41.9 sq.dm).
Weight-------------------8.8-9.9 lbs ( 4.0 kg).
Length-------------------50.7 in ( 128.7 cm).
Engine-------------------10-15cc
Motor size---------------1200-1500 Watts
Radio--------------------6 channels with 7 servos.
Electric Power Conversion Included.

“ Graphics and specifications may change without notice ”.

Code: SEA258

1
2
3
...
»

Содержание NORTH AMERICAN T-28 TROJAN



































Отзывы:

Нет отзывов

Похожие инструкции для NORTH AMERICAN T-28 TROJAN

Бренд: Team C Страницы: 33

Бренд: Parkside Страницы: 28

Super Decathlon

Бренд: PARKZONE Страницы: 44

Бренд: PARKZONE Страницы: 20

Бренд: L. G. B. Страницы: 37

DYSTOPIAN WARS MEXICO

Бренд: WARCRADLE STUDIOS Страницы: 6

THE GHOST HOUSE

Бренд: RavensBlight Страницы: 10

Бренд: Fisher-Price Страницы: 2

Lokpuffer Puff-H0

Бренд: Fichtelbahn Страницы: 2

Бренд: LEGO Страницы: 36

Deere CONSTRUCTION LOADER

Бренд: Peg-Perego Страницы: 52

Touch & Learn Activity Desk Deluxe

Бренд: VTech Страницы: 10

Mercedes-Benz SLK

Бренд: Rastar Baby Страницы: 14

Бренд: H-KING Страницы: 13

Бренд: Radica Games Страницы: 2

Pop-up Football Goal 2-in-1

Бренд: Dream Sports 24 Страницы: 16

Бренд: Fisher-Price Страницы: 10

Lionel Quantum-1 System

Бренд: QSI Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды