DURKOPP ADLER 911-211 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 200

DURKOPP ADLER 911-211 Скачать руководство пользователя страница 79

Machine head

Service Instructions 911-211 - 02.0 - 10/2016

78

Proper setting

1.

Press and turn the hand crank until the roller (5) is at the highest point
of the control cam (6).

2.

Press against the magnet armature (1).



The locking latch (2) can be swung out without clamping, and the dis-
tance between the locking latch (2) and locking pin (7) is not greater
than 0.1 mm.

To set the locking latch:

1.

Loosen the nut (4).

2.

Turn the threaded pin (3) and set the distance.

3.

Tighten the nut (4).

4.10 Setting the hook thread clamp

Cover

• Swivel up the machine head (

• Bobbin flap (

Fig. 63: Setting the hook thread clamp

WARNING

Risk of injury from sharp and moving parts!

Puncture or crushing possible.

Switch off the machine before you check and set
the hook thread clamp.

(1)

- Magnet armature

(2)

- Thread advancing device

(3)

- Hook thread clamp

①

②

③

«
...
77
78
79
80
81
...
»

Содержание 911-211









































































































































































































Отзывы:

Нет отзывов