DURKOPP ADLER 911-211 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 200

DURKOPP ADLER 911-211 Скачать руководство пользователя страница 16

Working basis

15

Service Instructions 911-211 - 02.0 - 10/2016

3.3

Removing and opening covers

In many types of setting work, you will have to remove the machine covers
in order to access the components.

This chapter describes how to remove and then refit the individual covers.
The text for each type of setting work then specifies only the cover that
needs to be removed at that particular time.

3.3.1 Access to the underside of the machine

Cover

To access the components on the underside of the machine, swivel up the
machine head.

Fig. 1: Access to the underside of the machine

Swiveling up the machine head

To swivel up the machine head:

1.

Release the locking lever (1) under the tabletop.

2.

Lift the machine head in the head cover area (2) and swivel up carefully.



The latch (4) latches into place.

WARNING

Risk of injury from moving parts!

Crushing possible.

Switch the machine off before removing or re-placing
covers.

(1)

- Locking lever

(2)

- Head cover

(3)

- Drive carriage

(4)

- Latch

①

②

③

④

«
...
14
15
16
17
18
...
»

Содержание 911-211









































































































































































































Отзывы:

Нет отзывов