DURKOPP ADLER 911-211 Скачать руководство пользователя страница 155

Страница: 155 / 200

Maintenance

Service Instructions 911-211 - 02.0 - 10/2016

154

8.3.3 Cleaning the filter element

Fig. 121: Cleaning the filter element

To clean the filter element:

Disconnect the machine from the compressed air supply.

Drain the water condensation (



p. 153

Loosen the water separator (2).

Loosen the filter element (1).

Blow out the filter element (1) using a compressed air gun.

Wash out the filter tray using benzine.

Tighten the filter element (1).

Tighten the water separator (2).

Tighten the drain screw (3).

10. Connect the machine to the compressed air supply.

NOTICE

Damage to the paintwork from solvent-based cleaners!

Solvent-based cleaners damage the filter.

Use only solvent-free substances for washing out the filter tray.

(1)

- Filter element

(2)

- Water separator

(3)

- Drain screw

①

②

③

Содержание 911-211









































































































































































































Результаты поиска

Содержание 911-211

Отзывы:

DURKOPP ADLER 911-211, Инструкция по эксплуатации, Страница: 155 / 200

Результаты поиска

Содержание 911-211

Отзывы: