DURKOPP ADLER 911-211 Скачать руководство пользователя страница 77

Страница: 77 / 200

Machine head

Service Instructions 911-211 - 02.0 - 10/2016

4.9.4 Setting the thread advancing device

Fig. 61: Setting the thread advancing device

Proper setting

• When the thread advancing device (1) is at rest, the distance between

the highest point of the control cam (6) and the roller (5) is 0.1 mm

• The control cam (6) makes contact with the clamping ring (4)

• The carrier (2) must have no axial play, but still run smoothly

Setting steps

Loosen all 4 threaded pins on the clamping ring (4).

Push the clamping ring (4) towards the hook bearing as far as it will go.

Tighten all 4 threaded pins on the clamping ring (4).

Loosen both threaded pins on the control cam (6).

Turn the lever (7) so that the threaded pin (9) on the body casting (3)
strikes the hook support.

Set the distance between the roller (5) and the highest point of the
control cam (6) to 0.1 mm.

WARNING

Risk of injury from sharp and moving parts!

Puncture or crushing possible.

Switch off the machine before you check and set
the thread advancing device.

(1)

- Thread advancing device

(2)

- Carrier

(3)

- Body casting

(4)

- Clamping ring

(5)

- Roller

(6)

- Control cam

(7)

- Lever

(8)

- Clamping screw

(9)

- Threaded pin

⑧

⑨

①

② ③ ④

⑤

⑥ ⑦

Содержание 911-211









































































































































































































Результаты поиска

Содержание 911-211

Отзывы:

DURKOPP ADLER 911-211, Инструкция по эксплуатации, Страница: 77 / 200

Результаты поиска

Содержание 911-211

Отзывы: