DURKOPP ADLER 911-211 Скачать руководство пользователя страница 156

Страница: 156 / 200

Maintenance

155

Service Instructions 911-211 - 02.0 - 10/2016

8.4

Checking the toothed belt

The condition of the toothed belt must be checked once a month.

Important

A damaged toothed belt must be replaced immediately.

Proper setting

• The toothed belt exhibits no cracks or fragile areas.

• When pressed with a finger, the toothed belt must yield no more than

10 mm.

8.5

Checking the thread suction device

Proper setting

The thread is sucked in properly. Check on a regular basis if the thread
suction device sucks in the thread properly without the walls of the hose
sticking together.

To check the thread suction device:

As soon as the thread is no longer sucked in properly, blow talcum
powder into the hose through the opening of the thread suction device.

8.6

Parts list

A parts list can be ordered from Dürkopp Adler. Or visit our website for fur-
ther information at:

www.duerkopp-adler.com

WARNING

Risk of injury from moving parts!

Crushing possible.

Switch off the machine before checking the
condition of the toothed belt.

Содержание 911-211









































































































































































































Результаты поиска

Содержание 911-211

Отзывы:

DURKOPP ADLER 911-211, Инструкция по эксплуатации, Страница: 156 / 200

Результаты поиска

Содержание 911-211

Отзывы: