DURKOPP ADLER 911-211 Скачать руководство пользователя страница 87

Страница: 87 / 200

Sewing unit

Service Instructions 911-211 - 02.0 - 10/2016

5.2.2 Changing the X drive

Fig. 70: Changing the X drive

Disassembling the X drive

To disassemble the drive:

Disconnect both plugs (4).

Loosen all 4 screws (1).

Pull off the motor and flange (3).

Assembling the X drive

To assemble the drive:

Insert a new motor and flange (3) on to the toothed belt (2).

Insert all 4 screws (1) and tighten them loosely.

Tension the toothed belt (2) using the screw (5).

Information

The toothed belt tension is set to the optimum value when the belt oscil-
lates at 384 Hz. Check the oscillation, for instance, using a device made
by Contitech.

Tighten all 4 screws (1).

Connect the plug (4).

(1)

- Screws

(2)

- Toothed belt

(3)

- Motor with flange

(4)

- Plug

(5)

- Screw

④

⑤

①

②
③

Содержание 911-211









































































































































































































Результаты поиска

Содержание 911-211

Отзывы:

DURKOPP ADLER 911-211, Инструкция по эксплуатации, Страница: 87 / 200

Результаты поиска

Содержание 911-211

Отзывы: