DURKOPP ADLER 911-211 Скачать руководство пользователя страница 49

Страница: 49 / 200

Machine head

Service Instructions 911-211 - 02.0 - 10/2016

4.6

Sewing foot lift

4.6.1 Setting the stroke position drive

Fig. 35: Setting the stroke position drive

Proper setting

The toothed rack must be 16.5

0.5 mm distant from the top edge (1) of

the stroke position housing. The threaded pins must be visible in the long
hole and must be horizontal.

Cover

• Motor cover (



p. 16

)

To set the stroke position drive:

Loosen the threaded pins (4).

Remove the gear wheel (3).

Move the toothed rack (2) to 16.5 mm below the upper stop.

Insert the gear wheel (3) so that the threaded pins (4) are horizontal.

Tighten the threaded pins (4).

WARNING

Risk of injury from sharp and moving parts!

Puncture or crushing possible.

Switch off the machine before you check and set
the stroke position drive.

(1)

- Top edge of the stroke position housing

(2)

- Toothed rack

(3)

- Gear wheel

(4)

- Threaded pins

16,5±0,5 mm

③

④

①

②

Содержание 911-211









































































































































































































Результаты поиска

Содержание 911-211

Отзывы:

DURKOPP ADLER 911-211, Инструкция по эксплуатации, Страница: 49 / 200

Результаты поиска

Содержание 911-211

Отзывы: