DURKOPP ADLER 911-211 Скачать руководство пользователя страница 51

Страница: 51 / 200

Machine head

Service Instructions 911-211 - 02.0 - 10/2016

Cover

• Head cover

• Motor cover (

To set the light barrier:

Loosen the screw (3).

Adjust the mounting plate (2) accordingly.

Tighten the screw (3).

Switch off and on the machine again.

Tap on

Service

Input the password (25483).

Tap on

Multitest

Eingänge/Ausgänge testen

(Test inputs/outputs)

Push the lever (4) up and monitor the display.



It will show 103 or -103.

Check that the toothed rack still has about 0.5 mm clearance from the
stop.

10. If necessary, set the light barrier again using the mounting plate.

4.6.3 Setting the left stop screw

Proper setting

The left stop screw (3) of the lifting gear must be set so that the lever (1)
performs no stroke when it is lying against the stop block (4). The levers
of the lifting gear (5) overlap.

Switch off and on the machine again.

Reference the machine.

Tap on

Extras

Service

Multitest

Hublage einstellen

(Set stroke position)

Tap on

Hüpfer/Drücker (Walking foot/presser foot)

until

the presser foot is selected.

Press and turn the hand crank and check that no stroke is performed.

WARNING

Risk of injury from sharp and moving parts!

Puncture or crushing possible.

Switch off the machine before you check and set
the stop screw.

Содержание 911-211









































































































































































































Результаты поиска

Содержание 911-211

Отзывы:

DURKOPP ADLER 911-211, Инструкция по эксплуатации, Страница: 51 / 200

Результаты поиска

Содержание 911-211

Отзывы: