DURKOPP ADLER 911-211 Скачать руководство пользователя страница 85

Страница: 85 / 200

Sewing unit

Service Instructions 911-211 - 02.0 - 10/2016

5.2

Changing the drives

5.2.1 Changing the sewing motor

Disassembling the sewing motor

To disassemble the sewing motor:

Cut off the cable ties.

Disconnect the motor cable from the control.

Removing the toothed belt cover (



p. 20

Fig. 68: Disassembling the sewing motor

Loosen the screws (6).

Remove the toothed belt (1).

Pull off the plate (3) with the motor (4).

Remove the toothed belt wheel (2).

To do so, loosen the screw on the toothed belt wheel.

Loosen the screws (5).

Remove the motor (4) from the plate (3).

WARNING

Risk of injury from sharp and moving parts!

Puncture or crushing possible.

Switch off the machine before changing the drives.

(1)

- Toothed belt

(2)

- Toothed belt wheel

(3)

- Plate

(4)

- Motor

(5)

- Screws

(6)

- Screws

④

⑥

③

①

⑤

②

Содержание 911-211









































































































































































































Результаты поиска

Содержание 911-211

Отзывы:

DURKOPP ADLER 911-211, Инструкция по эксплуатации, Страница: 85 / 200

Результаты поиска

Содержание 911-211

Отзывы: