DURKOPP ADLER 911-211 Скачать руководство пользователя страница 157

Страница: 157 / 200

Decommissioning

Service Instructions 911-211 - 02.0 - 10/2016

156

Decommissioning

You need to perform a number of activities if the machine is to be shut
down for a longer period of time or completely decommissioned.

To decommission the machine:

Switch off the machine.

Unplug the power plug.

If applicable, disconnect the machine from the compressed air supply.

Remove residual oil from the oil pan using a cloth.

Cover the control panel to protect it from soiling.

Cover the control to protect it from soiling.

Cover the entire machine if possible to protect it from contamination
and damage.

WARNING

Risk of injury from a lack of care!

Serious injuries may occur.

ONLY clean the machine when it is switched off.

Allow ONLY trained personnel to disconnect the
machine.

CAUTION

Risk of injury from contact with oil!

Oil can cause a rash if it comes into contact with
skin.

Avoid skin contact with oil.

If oil has come into contact with your skin, wash the
affected areas thoroughly.

Содержание 911-211









































































































































































































Результаты поиска

Содержание 911-211

Отзывы:

DURKOPP ADLER 911-211, Инструкция по эксплуатации, Страница: 157 / 200

Результаты поиска

Содержание 911-211

Отзывы: