DURKOPP ADLER 911-211 Скачать руководство пользователя страница 31

Страница: 31 / 200

Machine head

Service Instructions 911-211 - 02.0 - 10/2016

Machine head

4.1

Positioning the arm shaft crank

Proper setting

The 3 threaded pins (2) on the arm shaft crank (1) are seated completely
on the flat.

Cover

• Arm cover

Fig. 20: Positioning the arm shaft crank

To set the arm shaft crank:

Loosen all threaded pins (2) on the arm shaft crank (1).

Turn the arm shaft crank (1) such that the threaded pins (2) are seated
completely on the flat of the arm shaft.

Push the arm shaft crank (1) to the right as far as it will go.

Tighten all the threaded pins (2) on the arm shaft crank (1).

WARNING

Risk of injury from moving parts!

Crushing possible.

Switch the machine off before you check and set
the position of the arm shaft crank.

(1)

- Arm shaft crank

(2)

- Threaded pins

②

①

Содержание 911-211









































































































































































































Результаты поиска

Содержание 911-211

Отзывы:

DURKOPP ADLER 911-211, Инструкция по эксплуатации, Страница: 31 / 200

Результаты поиска

Содержание 911-211

Отзывы: