Digital Link DL600E Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 147

background image

5-2

DL600E E1 Data Multiplexer UserÕs Guide

Introduction

This chapter describes the front panel interface of the

DL600E

unit.

The front panel interface lets you:

¥

View and change the

DL600E

conÞguration from the

CONFIGURATION

menu

¥

Monitor and manage the

DL600E

unit from the

MONITOR

menu

¥

Run diagnostic tests on the

DL600E

unit from the

TEST

menu

The front panel interface is easy to use if you are an experienced user. If
you are not, the best way to learn the systemÕs contents and
organization is to use the terminal interface. It displays the system in
menus while the front panel interface displays only one line item at a
time.

Use the front panel when a terminal is not readily available. At times, it
is easier to use the front panel interface to perform a task rather than
connect a terminal to do the same from the terminal interface.

What You CanÕt Do From the Front Panel Interface

The front panel interface does not provide for setting:

¥

Alarm conditions and thresholds

¥

Superuser and Normal User passwords

¥

Modem connection and telephone numbers

You must use the terminal interface to set these parameters.

«
...
76
77
78
79
80
...
»

Содержание DL600E




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для DL600E

Бренд: Malmbergs Страницы: 20

Бренд: Rain Bird Страницы: 2

Бренд: VOLTCRAFT Страницы: 90

Бренд: ADTRAN Страницы: 145

Бренд: LXI Страницы: 6

Бренд: Di-LOG Страницы: 36

Бренд: Keysight Страницы: 57

Бренд: Brymen Страницы: 16

Бренд: PEWA Страницы: 156

Бренд: SW Stahl PROFI Tools Страницы: 8

Бренд: Maxwell Digital Multimeters Страницы: 15

Бренд: Maxwell Digital Multimeters Страницы: 37

Бренд: Gamry Страницы: 46

Бренд: TC Communications Страницы: 30

Бренд: Eproteca Страницы: 2

Бренд: metex Страницы: 55

Бренд: Keithley Страницы: 97

Бренд: Feig Electronic Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды