Digital Link DL600E Скачать руководство пользователя страница 85

Страница: 85 / 147

Using the Front Panel Interface

5-9

The UNIT CONFIG Submenu

The items in the

UNIT CONFIG

menu are shown below.

Use the

Down Arrows

to move from item to item. To activate edit

mode, press

ENTER

For information about the

UNIT CONFIG

items, refer to

Menu-4 Main

ConÞguration

in Chapter 3.

UNIT ID

and

Date and Time

Edit each item one character at a time. To move to the next
character, press

ENTER

COMM PORT CONF

submenu

You can display and modify the Comm Port settings only from
the front panel

COMM PORT

submenu. Refer to page

5-10

TEST LENGTH

Ñ01M, 15M, 60M, --- (Unlimited)

(DefaultÑUnlimited)

Test Length

Appears in

Menu-9 Diagnostics

in the terminal

interface.

For more information, refer to Chapter 6.

UNIT CONFIG

ENTER

UNIT ID HARRY

COMM PORT CONF

TEST LENGTH

HW REV D

ÐÐÐ

SW REV 2.5

NOV,12,95 10,46,58

read-only

Содержание DL600E




















































































































































Результаты поиска

Содержание DL600E

Отзывы:

Похожие инструкции для DL600E

Бренды по названию

Популярные бренды

Digital Link DL600E, Руководство пользователя

Результаты поиска

Содержание DL600E

Отзывы:

Похожие инструкции для DL600E

Бренды по названию

Популярные бренды