Digital Link DL600E Скачать руководство пользователя страница 91

Страница: 91 / 147

Using the Front Panel Interface

5-15

Displaying the Timeslot Allocation

To display the timeslot allocation for each port:

Press

ENTER

to open the

CONFIGURATION

and move to

TIMESLOT CONFIG

using the

Down Arrows

, then press

ENTER

to open.

A submenu appears, such as

TS CONF CONTIG

To see the timeslot allocation for port 1, press the

Arrow.

To see the allocation for port 2, press the

Arrow

again.

Repeat for the other ports (if you have them).

Example:

The TIMESLOT CONFIG Menu

The

TIMESLOT CONFIG

menu offers three allocation methods :

CONTIG

ALT

and

MANUAL.

Refer to ÒAllocating TimeslotsÓ in Chapter 3 for more information.

TS CONF CONTIG

TIMESLOT CONFIG

ENTER

TS CONF CONTIG

DTE01 TS

01 -- 31

DTE02 IDLE

Default timeslot allocation

TS CONF CONTIG

TS CONF MANUAL

TIMESLOT CONFIG

Содержание DL600E




















































































































































Результаты поиска

Содержание DL600E

Отзывы:

Похожие инструкции для DL600E

Бренды по названию

Популярные бренды

Digital Link DL600E, Руководство пользователя

Результаты поиска

Содержание DL600E

Отзывы:

Похожие инструкции для DL600E

Бренды по названию

Популярные бренды