Digital Link DL600E Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 147

background image

vi

Regulatory Compliance Standards

To maintain

EMC

Class

B

(CE

Label) compliance, shielded cables should be used with

the unit.

The Digital Link DL600E module complies with

¥

CE MARK

¥

BABT NTR4

¥

Austel

TS016

¥

Swedish

SS636334

¥

German

M†9a/b

¥

Australian AS 3260

¥

FCC part 15 Class A

¥

UL 1950 3rd Edition

¥

CAN/CSA C22.2. No. 950-95 3rd Edition

European harmonized standards:

¥

73/23/EEC

¥

91/31/EEC

¥

89/336/EEC

¥

93/68/EEC

¥

91/263/EEC

¥

2

Mbit/s

G703 (E1)

interface against

UK

speciÞcation

NTR4 (75

ohm unbal-

anced)

¥

2

Mbit/s

G.703 (E1)

interface against

CTR12 (120

ohm balanced, unstructured)

including protection test

¥

2

Mbit/s

G.703 (E1)

interface against

TBR13 (120

ohm balanced, structured)

including protection tests.

Under

89/336/EEC,

as amended by

92/31/EEC

and

93/68/EEC,

the DL600E was tested

in accordance with

EN50081-1 (1995)

and

EN50082-1 (1994)

to the following stan-

dards:

EN55022

Level

B, IEC 1000-4-2, ENV50140, ENV50141, IEC 1000-4-4,

ENV50142, EN61000-4-8,

and

EN61000-4-11.

Under

73/23/EEC

as amended by

93/68/EEC,

the DL600E

was tested to

IEC 950 (1994)

3rd edition

; EN

60950 (1992) 3rd edition. Under 91/263/EEC, this unit complies with the

Pan-european requirements set forth in CTR 12 and TBR 13.

Under 91/263/EEC this product complies with the requirements of Annex III for Pan-
European approval under CTR 12 and TBR 13 for 120 ohm operation. This information
is contained in a report prepared by KTL. This report was submitted to BABT with a
reference number: 1MST0400 and carries the BABT logo with the approval number:
AA607035.

168

«
...
4
5
6
7
8
...
»

Содержание DL600E




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для DL600E

OBID i-scan ID ISC.ANT.MUX

Бренд: Feig Electronic Страницы: 37

Бренд: Major tech Страницы: 16

Бренд: evertz Страницы: 24

Бренд: Paradyne Страницы: 10

Бренд: Paradyne Страницы: 14

Бренд: Sanwa Страницы: 2

Бренд: Gigahertz Solutions Страницы: 2

Бренд: APPA Страницы: 24

Бренд: CABAC Страницы: 23

Бренд: FANOX Страницы: 8

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 32

Бренд: Steinberg Systems Страницы: 21

Бренд: Steinberg Systems Страницы: 23

Бренд: Conrad Страницы: 91

Бренд: Mastech Страницы: 21

Бренд: Pro's Kit Страницы: 20

Бренд: Fieldpiece Страницы: 2

Бренд: Chauvin Arnoux Страницы: 138

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды