manualshive.com logo in svg

Digital Link DL600E, Руководство пользователя, Страница: 44 / 147

Поделиться
Скачать
Digital Link DL600E Скачать руководство пользователя страница 44

3-10

DL600E E1 Data Multiplexer UserÕs Guide 

¥

Parameters of the Data and AUX E1 ports in 

Menu-5 Data Port 

ConÞguration

¥

Timeslot allocations in 

Menu-6 Timeslot ConÞguration

¥

SNMP

 parameters in 

Menu-0 SNMP ConÞg 

(if required)

¥

Alarm conditions, thresholds, and passwords in 

Menu-7 Alarm 

I 

and

 Menu-8 Alarm II 

About the Remote System 

The status and conÞguration of the remote system appear on the menuÕs 
right side if the remote and local systems have an In-Band 
Communication Link over a national bit. The local DL600E unit 
continuously polls the remote system for information and displays it on 
the screen. If the remote system stops responding for 30 seconds, its 
status and conÞguration do not appear on the menu; they reappear when 
the system responds.

Setting the Unit ID, Date and Time

Use 

Menu-4 Main ConÞguration

 to set the 

ID

, da

t

e and time.

SW Ver 1.0 MIB Ver 1.1   Digital Link DL600 Encore

2/24/96

HW Ver A                      Menu-4 Main Configuration

22:04:06

     Local:

 Remote: 

MAUI

 

UNIT

Protect Mode

Disabled

Disabled

NET

CRC4

Enabled

Enabled

Line Impedance

120 OHM

Main/Alt Sync.

INT/INT

NET/int

In-Band Communications Bit

4

4

AUX

CRC4

Enabled

Line Impedance

75 OHM

0-SNMP Config.1-Main Status  2-Data DTE Status  3-Reports 4-Main Config.

5-Data Port Config. 6-Timeslot Config. 7-Alarm I 8-Alarm II 9-Diagnostics 

Type Arrow keys to move the selection, RETURN to change a selection

or type 0 through 9 for a new menu:

Figure 3-2

Menu-4 Main ConÞguration 

OAHU

 

   

Date

Time

  Unit ID

These parameters

with an AUX port

appear only on a unit

Содержание DL600E




















































































































































Отзывы:

Нет отзывов