Digital Link DL600E Скачать руководство пользователя страница 48

Страница: 48 / 147

3-14

DL600E E1 Data Multiplexer UserÕs Guide

The system prompts (if

is chosen):

Please start the XMODEM download.
Type CTRL-X to abort.

From the terminal, select

XMODEM

transmission and specify

the Þlename of the new software on the diskette.

The system informs you of a successful or unsuccessful
operation. In each case (including a cancelled operation), it
prompts:

Please type Y to reset the unit. [Y]:

Type

to reset the unit.

The system prompts:

Please wait... Unit is being reset.

System Messages and Error Indicators

During the operation, integrity check results are indicated by

BAD

in the

DOWNLOAD UTILITY

menu:

DOWNLOAD UTILITY 0.1

Operational Software:

Updated Download Utility:

Factory Download Utility:

Download RAM allocated:

In the case of the Þrst three items, the operation has proceeded correctly
even when Ò

BADÓ

appears.

Operational SoftwareÑ

BAD

indicates the DL600E operational software

stored in the

FLASH

failed either its

CRC

check or unused

FLASH

was

not set to the expected value.

Updated Download UtilityÑ

BAD

indicates the DL600E download utility

stored in the

FLASH

failed either its

CRC

check or unused

FLASH

was

not set to the expected value.

Factory Download UtilityÑ

BAD

indicates the DL600E factory-installed

download utility stored in the

FLASH

failed either its

CRC

check or

unused

FLASH

was not set to the expected value.

Содержание DL600E




















































































































































Результаты поиска

Содержание DL600E

Отзывы:

Digital Link DL600E, Руководство пользователя, Страница: 48 / 147

Результаты поиска

Содержание DL600E

Отзывы: