Digital Link DL600E Скачать руководство пользователя страница 36

Страница: 36 / 147

3-2

DL600E E1 Data Multiplexer UserÕs Guide

This chapter describes how to conÞgure the

DL600E

unit using its terminal

interface.

Note:

The DL600E unit can be partially conÞgured from the

front panel, which is the same as conÞguring from a
terminal. Instructions for using the front panel to conÞgure
the DL600E unit is found in

Chapter 5, Using the Front

Panel Interface

Preparing to ConÞgure

During the initial

DL600E

conÞguration you must:

ConÞgure the Comm port from the front panel (if a terminal
or

SNMP

manager is to monitor the unit)

Set the DL600E

address,

subnet mask to establish a Telnet

connection to the

DL600E

unit

Set up to three Trap

NMS IP

addresses and community strings

Menu-0 SNMP ConÞg

to use an

SNMP

workstation

You must also perform the initial conÞguration of the unit

and Comm

Port from the front panel. The

addresses and mask are conÞgured from

the terminal interface.

Keeping a Record

We suggest you keep a written record of each unitÕs conÞguration. Use the

Configuration Worksheet

provided at the end of Appendix A.

Connecting an ASCII Terminal

To use the terminal interface, you

must first

conÞgure the

Comm

Port

from the

front panel

of the

DL600E unit

. Refer to Chapter

for

information on how to conÞgure the

DL600E

unit with the front panel.

Connect a terminal to the

DL600E

Comm Port either directly, through a

terminal server, or through a modem.

Before you connect the terminal, make sure the baud rate, parity bit,
word length and stop bit settings on the terminal or modem

match

the

DL600E

settings.

Содержание DL600E




















































































































































Результаты поиска

Содержание DL600E

Отзывы:

Похожие инструкции для DL600E

Бренды по названию

Популярные бренды

Digital Link DL600E, Руководство пользователя

Результаты поиска

Содержание DL600E

Отзывы:

Похожие инструкции для DL600E

Бренды по названию

Популярные бренды