Digital Link DL600E Скачать руководство пользователя страница 18

Страница: 18 / 147

DL600E E1 Data Multiplexer UserÕs Guide

Digital Link Technical Support

If you encounter a problem with the DL600E unit, prepare the
following information and contact Digital Link Technical Support.

What is the software revision?

What is the hardware revision?

How is the unit conÞgured?

When was the unit conÞguration last changed? How?

What is connected to the unit (routers, test equipment, and so on)?

What operation was in progress when the failure occurred?

What was the state of the

LED

s on the front panel when the failure

occurred?

What methods did you use in trying to resolve the problem?

Is the problem repeatable? If so, how?

Are the cables attached securely to the unit?

Are the cables shielded?

What is the unitÕs clock source?

Who can be contacted to discuss the problem?

What is the unit password(s)?

What information is on the conÞguration, error statistics and event
history display screens at the time of the error? (Please provide a
hard copy capture of the screens.)

Tech Support U.S.A.:

Company FAX:
Email:

(408) 745-4200

(408) 745-6250
[email protected]

Hours:

24-hour service, 7 days a week

Tech Support UK:

+44 171 244-7660

Содержание DL600E




















































































































































Результаты поиска

Содержание DL600E

Отзывы:

Похожие инструкции для DL600E

Бренды по названию

Популярные бренды

Digital Link DL600E, Руководство пользователя

Результаты поиска

Содержание DL600E

Отзывы:

Похожие инструкции для DL600E

Бренды по названию

Популярные бренды