Digital Link DL600E Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 147

background image

Monitoring and Managing the DL600E Unit

4-7

Menu-1 Main Status Parameters

All parameters in Menu-1 are read-only.

Unit Status

Unit Status

indicates if the DL600E unit is operating normally or

if any special conditions exits. When the DL600E unit is
executing a test, the test is indicated in this Þeld. (If the test is
running on a port, the port appears in parenthesis.

Indication

Description

Normal

No abnormal conditions exist

Self Test

Unit is running self test.

DTE

Loopback (fraction)

Unit is in DTE

loopback

AUX E1 Loopback
(fractional)
NET

Loopback (full)

Unit is in network loopback.

PLD

Loopback (fraction)

Unit is in payload loopback.

Send User 1

(fraction)

Unit is sending

User 1

pattern.

Send User 2

(fraction)

Unit is sending

User 2

pattern.

Send 1:1

(fraction)

Unit is sending alternate 1s and 0s pattern.

Send 1:2

(fraction)

Unit is sending standard loop down remote code
continuously.

Send 1:4

(fraction)

Unit is sending standard loop up remote code
continuously.

Send 1:7

(fraction)

Unit is sending

1:7

pattern.

Send 3:24

(fraction)

Unit is sending

3:24

pattern.

Send QRW

(fraction)

Unit is sending

QRW

code.

Send All 1s

(fraction)

Unit is sending all ones signal.

Send All 0s

(fraction)

Unit is sending all zeros signal.

LP UP

Remote (fraction)

Unit is sending loopdown code to remote unit for
15

seconds.

LP DN

Remote (fraction)

Unit is sending loopup code to remote unit for 15

seconds.

Send RAI

Unit is sending RAI (Remote Alarm Indication).

No Clock

Clock source has failed.

Lamp Test

Unit is undergoing

Lamp Test

.

«
...
69
70
71
72
73
...
»

Содержание DL600E




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для DL600E

Бренд: Kane Страницы: 24

Бренд: Zico Страницы: 19

Бренд: Benning Страницы: 41

Бренд: Somogyi Страницы: 40

Бренд: Iso-Tech Страницы: 4

Бренд: Iso-Tech Страницы: 32

Бренд: Keysight Страницы: 57

Бренд: Kaiweets Страницы: 32

Бренд: UNI-T Страницы: 51

Бренд: LIMIT Страницы: 149

Бренд: Pro's Kit Страницы: 28

Бренд: Mastech Страницы: 10

Бренд: Campbell Страницы: 46

Бренд: Delton Страницы: 11

Бренд: Paradyne Страницы: 12

Бренд: UNI-T Страницы: 2

Бренд: Emos Страницы: 36

Бренд: Racal Instruments Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды