Digital Link DL600E Скачать руководство пользователя страница 141 | Manualshive

Страница: 141 / 147

background image

Glossary

G-9

scrambler

Ñ A device or software program that encodes data for encryption.

It distorts a voice or data conversation so that only another like device can Þg-
ure out the content of the message.

SD (Send Data)

Ñ A signal from

DTE

to

DSU/CSU.

secondary channel

Ñ A subchannel derived from the main channel. It does not

carry data messages and is used for diagnostic or supervisory purposes.

serial interface

Ñ Data channel that transfers digital data in a serial fashion:

one bit after the other. Communications lines are generally serial, thus
modems are connected to the computer via a serial port. So are mice and
scanners. Serial interfaces have multiple lines, but only one is used for data.
Contrast with parallel interface. See

RS232

.

serial port

Ñ I/O connector used to attach a modem, mouse, scanner or other

serial interface device to the computer. The typical serial port uses a DB25 or

DC9

connector, which on the back of a PC is a 25-pin male or 9-pin male

connector. Contrast with parallel port. See RS232.

serial transmission

Ñ A sequential transmission of bits constituting an entity

of data over a data circuit.

SG (Signal Ground)

Ñ A signal from

DTE

to

DSU/CSU.

simplex current

Ñ One way transmission used by Telco to provide power to

repeaters.

SLIP (Serial Line IP)

Ñ

A TCP/IP

protocol that allows

IP

packets to be trans-

mitted over a serial link, such as a dial-up or private telephone line.

SMDS (Switched Multimegabit Data Service)

ÑA fast-packet technology

based on the connection-less data networking capability described in the

IEEE

802.6

specification. The data format for

SMDS

is Òcell oriented.Ó

SMDS

does

not support voice.

smooth clock

Ñ A clock that eliminates gaps created during frame bit

removal.

SNMP (Simple Network Management Protocol)

Ñ A widely-used network

monitoring and control protocol. Data is passed from

SNMP

agents (hardware

and/or software processes reporting activity in each network deviceÑhub,
router, bridge, an so on.) to the workstation console used to oversee the net-
work. The agents return information contained in a

MIB

(Management Infor-

mation Base), which is a structure that deÞnes what is obtainable from the
device and what can be controlled.

«
...
139
140
141
142
143
...
»

Содержание DL600E




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для DL600E

Бренд: Fujitsu Страницы: 198

Бренд: APPA Страницы: 33

Бренд: IEK Страницы: 28

Бренд: GB Страницы: 3

Бренд: GB Страницы: 3

Бренд: Prema Страницы: 153

Бренд: FlowKinetics Страницы: 41

Бренд: XFtp Страницы: 44

Бренд: Paradyne Страницы: 161

Бренд: Campbell Страницы: 42

Бренд: Patton electronics Страницы: 21

Бренд: ADWA Страницы: 28

Бренд: Craftsman Страницы: 32

Бренд: CABAC Страницы: 23

MUX DVBS2-COFDM CI

Бренд: Televes Страницы: 36

Бренд: System Q Страницы: 9

Бренд: System Q Страницы: 18

Бренд: Net to Net Technologies Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды