Digital Link DL600E Скачать руководство пользователя страница 66

Страница: 66 / 147

4-2

DL600E E1 Data Multiplexer UserÕs Guide

Introduction

The DL600E unit collects and displays performance data as well as
additional data useful for network troubleshooting.

You can monitor and manage the unit from a terminal, remote terminal
Telnet connection, or an

SNMP

management station.

The DL600E unit monitors the

line continuously and displays all

collected data on the terminal screen.

The terminal interface menus enable you to:

Display or modify the

network conÞguration in

Menu-4

Main ConÞguration

ConÞgure alarm conditions, passwords, and modem
connection in

Menu-7 Alarm I

and

Menu-8 Alarm II

Monitor the status of the

network, AUX E1 port, and data

ports in

Menu-1 Main Status

and

Menu-2 Data DTE Status,

respectively.

Monitor the

performance data base in

Menu-3 Performance

Reports

This chapter describes how to monitor the DL600E status, display
performance reports and conÞgure alarm conditions.

Logging on to the DL600E

There are two ways to access the DL600E terminal interface:

From a terminal connected (directly or through a modem) to
the DL600E Comm Port

From a remote terminal Telnet connection

User Access Rights

Two levels of access rights are available when you log on to the DL600E
unit:
¥

Superuser access rights

Normal User access rights

With the

Superuser

password, you can:

Log off a

Normal User

already logged on the DL600E unit

Содержание DL600E




















































































































































Результаты поиска

Содержание DL600E

Отзывы:

Похожие инструкции для DL600E

Бренды по названию

Популярные бренды

Digital Link DL600E, Руководство пользователя

Результаты поиска

Содержание DL600E

Отзывы:

Похожие инструкции для DL600E

Бренды по названию

Популярные бренды