Digital Link DL600E Скачать руководство пользователя страница 57

Страница: 57 / 147

ConÞguring the DL600E Unit

3-23

Trap

(text string) (Default

public)

Enter an alphanumeric text string (maximum

Ñ32

characters)

which the DL600E

SNMP

agent inserts in

SNMP TRAP

s it

sends to the

SNMP

management stations.

ConÞguring Two Levels of Access Rights

You can create two levels of access rights to the DL600E terminal
interface:

Superuser access rights

and

Normal User access

rights

Do this by entering unique

Superuser

and

Normal User

passwords in

Menu-8 Alarms II

Superuser Access Rights

The superuser can:

Log off a

Normal User

already logged on

Change both passwords

Clear both passwords giving

Superuser

access to all users

Assigning User Passwords

It is important to

specify unique Superuser and Normal User

passwords

Menu-8 Alarms II

Since two access methods to the DL600E unit can be used (a terminal
connection or a

Telnet

connection) an unknown user could gain

exclusive control to the DL600E unit if the

Superuser

and

Normal User

passwords do not have unique values.

No passwords set

The Þrst user that logs on in a Òno passwords setÓ

situation and sets one or both passwords gains exclusive control of the
terminal interface.

One password only set

If only one password is set, both passwords

become the same. The Þrst user logging on with the password has

Superuser

rights and can change both passwords gaining exclusive

control of the terminal interface.

Содержание DL600E




















































































































































Результаты поиска

Содержание DL600E

Отзывы:

Digital Link DL600E, Руководство пользователя, Страница: 57 / 147

Результаты поиска

Содержание DL600E

Отзывы: