Digital Link DL600E Скачать руководство пользователя страница 105

Страница: 105 / 147

Diagnosing the DL600E Unit

6-3

User
selectable

Test

status

parameters

Selected test

The Diagnostics Menu

When running a test, you can:

Initiate loopbacks and tests on the full bandwidth or on the
data port fraction

Set programmable test patterns

Figure Figure 6-1 shows an example of

Menu-9 Diagnostics.

SW Ver 2.0 MIB Ver 1.2 Digital Link DL600 Encore4/22/95

HW Ver AMenu-9 Diagnostics00:00:36

Local: MARS

Remote: VENUS

Current TestPLD Lpbk(FULL)

Idle

Pattern Test StatusIdle

Idle

Last Self Test ResultSelf Test PassedSelf Test Passed

CRC4 Errors0

Code Violations0

Pattern Error Counter------------------------

FractionFull Bandwidth

DATA3

Test Length1 Min.

15 Min.

Test

Loop Payload

DTE Loopback

Full Bandwidth Loop CodeStandard

Standard

Fractional Loop CodeV.54

Disabled

USER1 Pattern0011001100110011001 10011

10011

USER2 Pattern000100010001000100010001

001001000

LOCAL ID=MARS Payload Loopback Test (Full BW) start at 16:08 May 22, 1995

0-SNMP ConÞg. 1-Main Status 2-Data DTE Status 3-Reports 4-Main ConÞg.

5-Data Port ConÞg. 6-Timeslot ConÞg. 7-Alarm I 8-Alarm II 9-Diagnostics

Arrow keys move the selection, RETURN changes a selection, S starts a test,

E ends a test, C clears the Pattern Error Counter, 0 through 9 start a new menu.

Figure 6-1

Menu-9 Diagnostics

Loop Payload

Содержание DL600E




















































































































































Результаты поиска

Содержание DL600E

Отзывы:

Digital Link DL600E, Руководство пользователя, Страница: 105 / 147

Результаты поиска

Содержание DL600E

Отзывы: